The WaveShuttle Multi-Wave Selective gives precise measurement and control for Multi-Wave Selective soldering machines.

Multi-Wave Selective Soldering machines offer electronic manufacturers the fast throughput while maintaining the benefits of only introducing the solder wave to the areas where through hole components need to be soldered. The throughput increase does however results in a reduction in flexibility, with dedicated nozzle designs needed matching the assemblies being soldered in production. Different nozzle shapes and sizes employed in the production soldering tooling exhibit different dynamics when the PCB is presented to the solder. The perfect process would result in contact between PCB and solder occurring both simultaneous and for the same contacts time, until now it was not possible to measure these crucial parameters.

The SolderStar Multi-Wave PRO allows Production Engineers to better understand the contact dynamics of this soldering process. A compact and flexible instrument has been designed to allow dedicated test fixtures to be produced quickly and cost effectively for multi-wave soldering machines, measurement sensors are fitted to customer specific locations which correspond to the soldering areas within the multi-wave solder pot tooling, this technique provides contact time and difference data to quickly allow engineers to identify any problem areas within the tool design. Any differences in nozzle to PCB contact can be easily measured providing a powerful platform for process capability analysis, improvement and on-going testing.

Date Capture and Analysis

Captured data is download via USB or Wireless interface for analysis on the engineers computer. All parameters can be quickly analysed and using the unique Solderstar Process Checker functions allow good/bad limits to be defined to allow periodic process verification to be performed without the need for specialist knowledge.

The WaveShuttle Multi-Wave Pro is supplied with Wave Central PC Software, a dedicated package for the analysis of all key wave soldering and selective parameters.  Based on Solder Star’s interface and navigation system it allows users of other SolderStar products to perform detailed wave solder analysis with minimal training.

The post Solderstar | Multi Wave/Dip Solder Instruments appeared first on ASI Technologies.

Nozzle strikes on clinched components or the PCB due to PCB warp or general tolerances can result in the positioning mechanism of the machine becoming mis-aligned. X and Y positioning mechanism and speed are verified by sweeping the selective soldering nozzles between pre-defined datum’s. An array of stepped contact sensors are employed to allow nozzle wave height measurements to be made and periodically verified.

Flux Sensing

When crystallisation occurs in the selective fluxer nozzle mis-fluxing of components can occur causing problems with poor wetting or leaving un-activated flux on area of the assembly. To combat this problem SolderStar has developed flux measurement sensors which can be optionally installed to the measurement fixture, this allows for flux presence and position to be obtained as part of the daily tests.

Date Capture and Analysis

Captured data is download via USB or Wireless interface for analysis on the engineers computer. All parameters can be quickly analysed and using the unique Solderstar Process Checker functions allow good/bad limits to be defined to allow periodic process verification to be performed without the need for specialist knowledge.

The WaveShuttle Pro is supplied with Wave Central PC Software, a dedicated package for the analysis of all key wave soldering parameters.  Based on Solder Star’s interface and navigation system it allows users of other SolderStar products to perform detailed wave solder analysis with minimal training.

The post Solderstar | Mini-Wave Selective Analyzer appeared first on ASI Technologies.

This unique fixture incorporates two measurement systems to give the most comprehensive and repeatable measurement results of any analyser on the market today. Measurement of wave contact time, wave height, wave parallelism and temperature profile are all required to correctly setup the wave solder machine correctly, these measurements can now be captured in one single pass using this innovative and convenient device

The WaveShuttle Pro is designed for the rigours of daily production testing, manufactured from 10mm anti-static composite and fitted with durable titanium side rails. This intelligent measurement fixture incorporates titanium contact sensors on the underside that capture wave parameters data as it moves through the solder wave, including a true measurement of wave height. Additionally the system measures preheat profiles and solder pot temperatures.

Graphical Analysis of Chip/Main Wave Shape & Contact

Date Capture and Analysis

All key process parameters are captured with single run through the machine, data is then download via USB or Wireless interface for analysis on the engineers computer. All parameters can be quickly analysed and using the unique Solderstar Process Checker functions allow good/bad limits to be defined to allow periodic process verification to be performed without the need for specialist knowledge.

Instant Good/Bad Indication

The WaveShuttle Pro is supplied with Wave Central PC Software, a dedicated package for the analysis of all key wave soldering parameters.  Based on SolderStar’s interface and navigation system it allows users of other SolderStar products to perform detailed wave solder analysis with minimal training

The post Solderstar | Wave Solder Machine Analyser appeared first on ASI Technologies.